r-S168 Stand-alone PCB Separator offers an automatic solution for PCB routing. High-speed motor spindle is adopted to solve the main problems of edge stirring and bounding wire / floor crashing during the traditional hand-banding or punching depaneling process.

Aiming
A 10x zoom CCD camera is attached to increase the accuracy of point setting, but not compromise the programming time.

Shaping
In order to minimize the cutting pressure, a max. 50000 rpm motor spindle is used. Our PC-based motion controller is with the functions of linear and circular interpolations to meet the routing needs of the PC boards with different shapes.

Safeguarding
The safety-door is designed to protect the user from any potential hazard during the operation. The door will be automatically shut down before the operation stars; however, the routing and cutting process can be scanned through the transparent door plank.

Cutting tool diameter 0.8 ~ 3.0 mm
Precision of positioning ±0.01mm
Number of axis control (X, Y, Z)
Travel stroke X:390mm, Y:390mm, Z:60mm
Max. driving speed X, Y: 750mm/sec, Z: 325mm/sec
Max. cutting speed X, Y, Z: 50mm/sec
Spindle motor High speed variable frequency motor 150W
Motor of axes 200W AC servo motor
Cutting ability Linear, arc, and circular cutting
Programming Direct coordinate input or jog teaching with a 10x CCD camera
Routing bit sectioning Max. 3 sections
Program backup 31/2 floppy disk
Power supply 3phase AC220V 50Hz / 60Hz; 2.5 kw (vacuum cleaner included)
Air 5 kg/cm2
Size 1013 x 1046 x 1737 mm
Weight 450 kg

2-way sliding work exchanger creates a simultaneously in-and-out working process to limit the idle time, which in turn reaches the utmost output value

Routing Bit Sectioning
The user may set a designated distance, and have the routing bit shift-up or -down in order to make a new section of touting bit to cut boards for multiplying the life of the routing bit.

Route Duplication
The user only needs to set two referent points to duplicate a same route in saving programming time.

Windows
Windows system and Graphical User Interface (GUI) is adopted, which enables the user to learn and use the program easily. A 10 x zoom-in image is shown on screen for setting all points.

Cutting tool diameter 0.8 ~ 3.0 mm
Precision of positioning ±0.01mm
Number of axis control 3 axes (X, Y, Z)
Travel stroke X:430mm, Y:510mm, Z:60mm (SA)
Travel stroke X:330mm, Y:330mm, Z:60mm (SW)
Max. driving speed X, Y, Z: 50mm/sec
Max. cutting speed X, Y, Z: 50mm/sec
Spindle motor High speed variable frequency motor 150W
Motor of axes 200W AC servo motors
Cutting ability Linear, arc, and circular cutting
Programming Direct coordinate input or jog teaching with a 10x CCD camera
Routing bit sectioning Max. 3 sections
Program backup 31/2 floppy disk
PCB loading / unloading Manual
Setting fixture 2 stations
Power supply 3phase AC220V 50Hz / 60Hz; 2.5kw (vacuum cleaner included)
Air 5 kg/cm2
Size 1341 x 1682 x 1930 mm (SA)
Size 1125 x 1395 x 1930 mm (SW)
Weight 950 kg (SA)
Weight 800 kg (SW)
**Area Sensor is optional**

A fully automatic processing line is designed for loading, routing, separating and loading / unloading PC boards to achieve a "no-man" operation.

Loading / Unloading
The width of conveyer can be adjusted to fit the PCB size of works. The pick-and-place device improves the efficiency of the loading and unloading process.

2-way Sliding Exchanger
This work exchanger provides a simultaneously in-and-out working space to limit the idle time, which in turn reaches the utmost output value.

Touch Panel
Graphical User Interface (GUI) is adopted, and enables the user to function the touch panel easily.

Cutting tool diameter 0.8 ~ 3.0 mm
Precision of positioning ±0.01mm
Number of axis control 8 axes
3 axes for cutting; 1 axis for conveyor; 2 axes for pick & place; 2 axes for feeding;
Travel stroke X:330mm, Y:250mm, Z:60mm
Max. driving speed X, Y: 750mm/sec, Z: 325mm/sec
Max. cutting speed X, Y, Z: 50mm/sec
Spindle motor High speed variable frequency motor 150W
Motor of axes 200W AC servo motor
Programming 32 sets x 999 lines
Cutting ability Linear, arc, and circular cutting
Programming Direct coordinate input or jog teaching with a 10x CCD camera
Routing bit sectioning Max. 3 sections
Program backup 31/2 floppy disk
Man-machine interface Color LCD touch panel
Conveyor adjustment Manual
PCB loading Bridge conveyor
PCB unloading Robot arm
Setting fixture 2 stations
Power supply 3phase AC220V 50Hz / 60Hz; 3 kw (vacuum cleaner included)
Air 5 kg/cm2
Size 2337 x 1325 x 1659 mm
Weight 800 kg